November 24, 2018

ISO 3382-1 PDF

ISO. First edition. Acoustics — Measurement of room .. ISO , together with ISO and ISO , cancel and replace ISO. NBR ISO Acoustics – Measurement Of Room Acoustic Parameters – Part 1: Performance Spaces. Be notified when this Standard is updated or. In this paper a selection of the most important ISO parameters is at Hz. Room acoustic parameters described in ISO where derived.

Author: Doktilar Tojagore
Country: Lithuania
Language: English (Spanish)
Genre: Health and Food
Published (Last): 8 May 2016
Pages: 406
PDF File Size: 8.13 Mb
ePub File Size: 13.74 Mb
ISBN: 216-6-22414-289-7
Downloads: 77764
Price: Free* [*Free Regsitration Required]
Uploader: Goltiran

ISO specifies three levels of measurement accuracy: Revision of ISO Reverberation time in ordinary rooms 1 Scope This part of ISO specifies methods for the measurement of reverberation time in ordinary rooms. There are several reasons to measure reverberation time. This part of ISO is intended to contribute to the general understanding and acceptance of reverberation time for room quality and usability. These measures may be used to give warnings when the decay curve is not linear, and consequently the result should be marked as less reliable and not having a unique reverberation.

Thus, this part of ISO fills a gap among measurement standards ido acoustic properties of buildings. An alternative measurement technique, however, is to use a period of maximum-length sequence MLS type signal or other deterministic, flat-spectrum signal like a sine sweep and transform the measured response back to an impulse response. However, a room with up to two persons present may be allowed to represent its unoccupied state, unless otherwise specified.

Reverberation time measurements should be made in a room containing no people. This part of ISO does not repeat the technical details of ISObut deals with the measurement of reverberation time, only, in any kind of room. It is obvious that a very simple measurement is better than no measurement. Enviado por Christiele flag Denunciar. Second, reverberation time is measured to determine the correction term for room absorption inherent in many acoustic measurements, such as sound insulation measurements according to ISO all parts and sound power measurements according to ISO It is then labelled accordingly.

Most Related  LA BATALLA DE STALINGRADO WILLIAM CRAIG PDF

This requires a io level of at least 35 dB. It describes the measurement procedure, the apparatus needed, the required number of measurement positions, and the method for evaluating the data and presenting the test report.

SRPS EN ISO 3382-1:2013

However, in the vast majority of rooms, it is left to the design team to specify and design for a reverberation time that is reasonable for the purpose of a room. In some countries, building codes specify the required reverberation times in classrooms and other categories of room. Rooms may include domestic rooms, stairways, workshops, industrial plants, classrooms, offices, restaurants, exhibition centres, sports halls, and railway and airport terminals. For undated references, the latest edition of the referenced document including any amendments applies.

Thus, if T is derived from the time at which the decay curve first reaches 5 dB and 25 dB below the initial level, it is labelled T For other reverberation time measurements, ISO covers auditoria and performance spaces, and ISO absorption coefficient measurements ios a reverberation room.

ISO Acoustics – Measurement of Room Acoustic Parameters. Part 1 – Google Books

The measurement results can be used for correction of other acoustic measurements, e. The use of rotating microphones during the measurement of decay curves has been considered by the working group, and this procedure is found to be without a clear physical meaning and thus it is only accepted for the interrupted noise method and only when the result is used for a correction term.

Most Related  IMAMIA JANTRI 2012 PDF

However, a preference has been given to the 20 dB evaluation range for several reasons: The introduction of the option of a survey measurement is intended to promote more frequent measurement of reverberation time in rooms where it is relevant. With modern measuring equipment, the decay curves are normally not displayed and this may introduce a risk that abnormal decay curves are used for the determination of the reverberation time.

ISO 3382 2 2008

Annex A contains some additional information about the measurement uncertainty of the reverberation time. The traditional measuring technique is based on visual inspection of every single decay curve.

For this reason, Annex B introduces two new measures that quantify the degree of non-linearity and the degree of curvature of the decay curve. Performance rooms ISOAcoustics kso Application oso new measurement methods in building and room acoustics IECElectroacoustics — Octave-band and fractional-octave-band filters 3 Terms and definitions For the purposes of this document, the following terms and definitions apply.

If the measurement result is used for correction of a.

The main difference concerns the number of measurement positions and thus the time required for the measurements. For dated references, only the edition cited applies.