November 16, 2018

ISO 3382-1 PDF

ISO. First edition. Acoustics — Measurement of room .. ISO , together with ISO and ISO , cancel and replace ISO. NBR ISO Acoustics – Measurement Of Room Acoustic Parameters – Part 1: Performance Spaces. Be notified when this Standard is updated or. In this paper a selection of the most important ISO parameters is at Hz. Room acoustic parameters described in ISO where derived.

Author: Yolmaran Mim
Country: Mozambique
Language: English (Spanish)
Genre: Life
Published (Last): 17 July 2014
Pages: 317
PDF File Size: 11.63 Mb
ePub File Size: 19.28 Mb
ISBN: 154-4-48872-176-6
Downloads: 47889
Price: Free* [*Free Regsitration Required]
Uploader: Gardagor

Annex A contains some additional information about the measurement uncertainty of the reverberation time. For this reason, Annex B introduces two new measures that quantify the degree of non-linearity and the degree of curvature of the decay curve. It is obvious that a very simple measurement is better than no measurement.

ISO 3382 2 2008

3328-1 There are io reasons to measure reverberation time. Second, reverberation sio is measured to determine the correction term for room absorption inherent in many acoustic measurements, such as sound insulation measurements according to ISO all parts and sound power measurements according to ISO Reverberation time measurements should be made in a room containing no people.

In some countries, building codes specify the required reverberation times in classrooms and other categories of room. The introduction of the option of a survey measurement is intended to promote more frequent measurement of reverberation time in rooms where it is relevant. This part of ISO does not repeat the technical details of ISObut deals with the measurement of reverberation time, only, in any kind of room.

For undated references, the latest edition of the referenced document including any amendments applies. The traditional measuring technique is based on visual inspection of every single decay curve. If the measurement result is used for correction of a.

Most Related  VARIACION GENETICA PDF

An alternative measurement technique, however, is to use a period of maximum-length sequence MLS type signal or other deterministic, flat-spectrum signal like a sine sweep and transform the measured response back uso an impulse response. It describes the measurement procedure, the apparatus needed, the required number of measurement positions, and the method for evaluating the data and presenting the test report.

However, in the vast majority of rooms, it is left to the design team to specify and design for a reverberation time that is reasonable for the purpose of a room. Reverberation time in ordinary rooms 1 Scope This part of ISO specifies methods for the measurement of reverberation time in ordinary rooms. For other reverberation time measurements, ISO kso auditoria and performance spaces, and ISO absorption coefficient measurements in a reverberation room.

Performance rooms ISOAcoustics — Application of new measurement methods in building and 3382–1 acoustics IECElectroacoustics — Octave-band and fractional-octave-band filters 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. For dated references, only the edition cited applies.

ISO Acoustics – Measurement of Room Acoustic Parameters. Part 1 – Google Books

It is then labelled accordingly. Thus, this part of ISO fills a gap among measurement standards for acoustic properties of buildings. Thus, if T is derived from the time at which the 33822-1 curve first reaches 5 dB and 25 dB below the ios level, it is labelled T The use of rotating microphones during the measurement of decay curves has been considered by the working group, and this procedure is 382-1 to be without a clear physical meaning and thus it is only accepted for the interrupted noise method and only when the result is used for a correction term.

Most Related  RICK LATHAM ADVANCED FUNK STUDIES PDF

This part of ISO is intended to contribute to the general understanding and acceptance of reverberation time for room quality and usability. The main difference concerns the number of measurement positions and thus the time required for the measurements.

With modern measuring equipment, the decay curves are normally not displayed and this may introduce a risk that abnormal decay curves are used for the determination of the reverberation time.

However, a preference has been given to the 20 dB evaluation range for several reasons: Enviado por Christiele flag Denunciar. These measures may be used to give warnings when the decay curve is not linear, and consequently the result should be marked as less reliable and not having a unique reverberation.

If decay values of 5 dB to 35 dB below the initial level are used, it is labelled T The measurement results can be used for is of other acoustic measurements, e. However, a room with up to two persons present may be allowed to represent its unoccupied state, unless otherwise specified.

Rooms may include domestic rooms, stairways, workshops, industrial plants, classrooms, offices, restaurants, exhibition centres, sports halls, and railway and airport terminals. ISO specifies three levels of measurement accuracy: First, the sound pressure level from noise sources, the intelligibility of speech, and the perception of privacy in a room are strongly dependent on reverberation time. This requires a signal-to-noise level of at least 35 dB.

Revision of ISO